Forums » Req. WJ2(ESP32) support »
Project 1: Road safety warning light, unable to build
Added by arya radi almost 2 years ago
Hi
I'm a student trying to use Waijung 2 for my project. So i started by trying to do "Project 1: Road safety warning light".
I already followed the instructions closely, and here i already tried using WiFi (STA) and the Serial modes. I use ESP32 Wrover
When i built the project, it always fails. i don't know why. I attached a picture of what was noticeable to me in the diagnostics viewer, and i also attached a txt. file of it
Please help because i have a deadline.
LearnProject1_20230208_155116.txt | LearnProject1_20230208_155116.txt | 408 KB | Diagnostics viewer | ||
clipboard-202302081600-ogquz.png | View clipboard-202302081600-ogquz.png | 100 KB | Screenshot | ||
LearnProject1_20230208_155116.txt | LearnProject1_20230208_155116.txt | 408 KB |
Replies (13)
RE: Project 1: Road safety warning light, unable to build - Added by Parth Maheshwari (พาร์ท) almost 2 years ago
Hello Arya,
Thank you for reaching out. I have tried this demo on my end.
Currently your file path length for where you have stored the Simulink file is very long. Could you please try using a shorter file path? My file path is 23 characters long and builds without any problems. Try to limit yours to 30 characters.
Let me know how it goes.
Sincere regards,
Parth Maheshwari
RE: Project 1: Road safety warning light, unable to build - Added by arya radi almost 2 years ago
Hi,
Thanks for the fast reply, I did try using a shorter path but the problem still persists
regards,
RE: Project 1: Road safety warning light, unable to build - Added by Parth Maheshwari (พาร์ท) almost 2 years ago
Could you attach the entire log .txt file too please?
RE: Project 1: Road safety warning light, unable to build - Added by arya radi almost 2 years ago
hi,
i used an even shorter path this time, still doesn't work
RE: Project 1: Road safety warning light, unable to build - Added by Parth Maheshwari (พาร์ท) almost 2 years ago
I think you attached the older log file. Could you please attach the one after making the path shorter?
RE: Project 1: Road safety warning light, unable to build - Added by arya radi almost 2 years ago
oh yeah sorry, here it is.
And i also attached the slx file in case needed
RE: Project 1: Road safety warning light, unable to build - Added by Parth Maheshwari (พาร์ท) almost 2 years ago
Hi Arya,
Firstly, when I opened your model, it looked like this:
The connection to the Digital Output block was broken and no GPIO pin was selected in the Digital Output block. Could you please check this?
Secondly, I fixed the broken link, selected a GPIO pin, ran it in External Mode via Serial (make sure you select the correct COM Port, UART Tx and Rx pins), removed the lamp and tried to build it with your configurations i.e. ESP32S3, MATLAB 2022b. It builds without problems for me.
Please schedule a technical session with us here if it still cannot build for you. We can debug your problem on Zoom in real-time.
Sincere regards,
Parth Maheshwari
RE: Project 1: Road safety warning light, unable to build - Added by Parth Maheshwari (พาร์ท) almost 2 years ago
Please also try using another ESP32 board if that's a possibility.
RE: Project 1: Road safety warning light, unable to build - Added by arya radi almost 2 years ago
i deleted the dashboard element and reconnected the source to the digital output. But it still doesn't work, and ESP32 WROVER is all i have.
It keeps failing here.
Guess I'll try the technical session.
RE: Project 1: Road safety warning light, unable to build - Added by Parth Maheshwari (พาร์ท) almost 2 years ago
Have you tried running the file provided on our website?
RE: Project 1: Road safety warning light, unable to build - Added by arya radi almost 2 years ago
i just tried it, it's still the same error
RE: Project 1: Road safety warning light, unable to build - Added by Parth Maheshwari (พาร์ท) over 1 year ago
Hi Arya,
Please do upload your build folder (.rar file) and complete log from the diagnostic viewer (.txt file)
We will keep trying to solve your issue. In the meantime, if you do give it a try on another ESP32/another computer/another MATLAB version, please let us know the result.
Sincere regards,
Parth
RE: Project 1: Road safety warning light, unable to build - Added by arya radi over 1 year ago
HI, sorry, i forgot to do it yesterday
Here it is